Frequency bands
•
EGSM 900, GSM 1800
•
Compliant to GSM Phase 2/2+
GSM class: Small MS
Transmit power:
•
Class 4 (2W) at EGSM 900
•
Class 1 (1W) at GSM 1800
GPRS connectivity
•
GPRS multi-slot class 10
•
GPRS mobile station class B
Data Services
•
GPRS data downlink transfer: max. 85.6 kbit/s
•
GPRS data uplink transfer: max. 42.8 kbit/s
•
Support of PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol) for PPP connections
•
Support of PBCCH (Packet Switched Broadcast Control Channel) for enhanced GPRS performance
•
CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbit/s, non-transparent, V.110
•
WAP compliant
•
Internet services: TCP, UDP, HTTP, FTP, SMTP, POP3
SMS
•
MT, MO, CB, Text and PDU mode
•
SMS storage: SIM card plus 25 SMS locations in the mobile equipment
•
Transmission of SMS alternatively over CSD or GPRS (user-defined)
•
MMS compliant
Fax: Group 3, Class 2
Onboard SIM card interface
•
Supported SIM card: 3 V
Coding scheme CS 1, 2, 3, 4
Optical isolation: 1 kV DC
One antenna connector at front panel
•
For the use of an external antenna
•
Rugged screw connection
Please note that MEN does not offer SIM cards or mobile telephony contracts!
GPS Interface
20-parallel-channel GPS (Global Positioning System) receiver
GPS Band/Code: L1 frequency, C/A code
Integrated TCXO, RTC
Horizontal accuracy: better than 2.1 m (CEP) 5.2 m 2dRMS
Time To First Fix (TTFF):
•
Cold start: 34 s typ.
•
Warm start: 32 s typ.
•
Hot start: 0.5 s typ.
Sensitivity:
•
Acquisition: -155 dBm
•
Navigation: -157 dBm
•
Tracking: -159 dBm
GPS modes
•
TricklePower™ mode for power saving
•
Push-To-Fix™ mode
Protocol: NMEA 0183
•
SiRF® binary messages: altitude, longitude, elevation, velocity, heading, time, satellite tracking status, command/control messages
•
SiRF® binary interface: raw data
Antenna voltage supervision
3GPP compliance
Optical isolation: 1 kV DC
One antenna connector at front panel
•
For the use of an external active antenna
•
Rugged screw connection
UARTs
Two channels
Accessible via onboard connectors
Physical interface at front panel using SA-Adapters™
•
Two SA-Adapters™ can be directly plugged within 4HP
•
Different physical layers depending on SA-Adapter™: RS232, RS422, RS485 with or without optical isolation
•
SA-Adapters™ to be ordered separately
Data rates up to 2 Mbit/s
60-byte transmit/receive buffer
Handshake lines: full support; lines depend on SA-Adapters™
Front Connections
Two Reverse SMA antenna connectors
Two cut-outs for SA-Adapters™
FPGA
Standard factory FPGA configuration:
•
Main bus interface
•
16Z057_UART - UART controller (controls in-system GSM-R/GPS communication and UARTs)
•
16Z045_FLASH - Flash interface
The FPGA offers the possibility to add customized I/O functionality. See FPGA.
CompactPCI® Bus
Compliance with CompactPCI® Core Specification PICMG 2.0 R3.0
Peripheral slot
32-bit/33-MHz PCI-to-PCI bridge
V(I/O): +3.3 V
Electrical Specifications
Supply voltage/power consumption:
•
Depends on mounted SA-Adapters™ and used functions
•
+5 V (-3%/+5%), 1900 mA max.
•
+3.3 V (-3%/+5%), 850 mA max.
Mechanical Specifications
Dimensions: conforming to CompactPCI® specification for 3U boards
Front panel:
•
4HP with ejector
•
3U single-slot front panel for two antenna and up to two UART connectors
Weight: 170 g
Environmental Specifications
Temperature range (operation):
•
-40..+85°C for all functions except GSM-R (screened)
•
GSM-R component only operable in -20..+70°C range (auto on/off)
•
Airflow: min. 10 m³/h
Temperature range (storage): -40..+85°C
Relative humidity (operation): max. 95% non-condensing
Relative humidity (storage): max. 95% non-condensing
Altitude: -300 m to + 3000 m
Shock: 15 g/11 ms
Bump: 10 g/16 ms
Vibration (sinusoidal): 2 g/10..150 Hz
Conformal coating (standard)
MTBF
189 239 h @ 40°C according to IEC/TR 62380 (RDF 2000)
Safety
PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC
Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)
Software Support
Driver software for Windows®, Linux, VxWorks®
For more information on supported operating system versions and drivers see Downloads.
Contact us
My MEN
You are logged off
Log in
Overview
This product is designed to work under Linux. See below for potentially available separate software packages from MEN.
This product is designed to work under Windows®. See below for potentially available separate software packages from MEN.
This product is designed to work under VxWorks®. For details regarding supported/unsupported board functions please refer to the corresponding software data sheets.
