PMC USM™ FPGA Development Kit

Technical Data

Evaluation Board AD99

50-pin connection to P599
• SCSI 2 connector
• 46 I/O signals from/to P599

Six SA-Adapter™ slots
• For direct onboard connection
• 46 I/O signals from/to SCSI 2 connector
• RS232 SA-Adapter™ SA1 included
• Eight GPIO lines included on slot 3

Three 20-pin I/O connectors
• 46 I/O signals from/to SCSI 2 connector

Eight user LEDs at front, driven by I/O signals

PMC P599 (USM™ main module)

CPU
• Nios® II soft processor
• 66MHz

Memory
• 32MB DDR2 SDRAM, soldered
• 2MB non-volatile Flash, for FPGA data and Nios® firmware

I/O at front panel (SCSI 2 connector)
• One LVTTL UART (for RS232 on AD99 via SA1 SA-Adapter™)
• Eight GPIO lines

Functions in FPGA
• Main bus interface
• Altera® SOPC Unit incl. Nios® II/f soft processor, GPIO, UART and DDR2 SDRAM control
• Wishbone-to-Avalon®/Avalon®-to-Wishbone bridges
• Chameleon Table V2
• Interrupt controller, SMBus controller
• PCI to Wishbone bridge, ID EEPROM emulation
• 16Z045_FLASH - Flash interface
• 16Z034_GPIO - GPIO controllers (2 IP cores, for onboard LEDs and 8-bit I/O)
• The FPGA offers the possibility to add customized I/O functionality. See FPGA.

USM™ Slot
• One slot populated with bare USM™ module US0
• US0 only passes through signals between the FPGA and the front connector and reduces +5V input levels to 3.3V system I/O level

Connection to evaluation board
• SCSI 2 connector, 50-pin HP D-Sub receptacle
• 46 I/O signals from/to evaluation board, FPGA-controlled

Eight front-panel LEDs, FPGA-controlled

PMC Characteristics (PCI)
• Compliant with PCI Specification 2.2
• 32-bit/33-MHz, 3.3V V(I/O)
• Target

Accessories

SA1 RS232 SA-Adapter™

SCSI 2 cable

Please note that the kit does not include an PMC carrier board! You should install the PMC module on a suitable carrier in a test system of your choice.

Electrical Specifications

Supply voltage/power consumption:
• P599 with US0: +5V (-3%/+5%), 1000mA max.
• AD99: +5V, consumption only depends on SA-Adapter™ used, current drawn on I/O lines and LEDs driven, with 1 SA1 and all 8 LEDs on approx. 100mA typ.
• SA1: +5V (-3%/+5%), 40mA typ.

MTBF:
• PMC USM™ Development Kit (total): 363,780h @ 40°C according to IEC/TR 62380 (RDF 2000)
• P599: 669,963h @ 40°C according to IEC/TR 62380 (RDF 2000)
• US0: 1,989,261h @ 40°C according to IEC/TR 62380 (RDF 2000)
• AD99: 1,469,985h @ 40°C according to IEC/TR 62380 (RDF 2000)
• SA1: 1,870,000h @ 50°C (derived from MIL-HDBK-217F)

Mechanical Specifications

Dimensions:
• P599: conforming to M-Module™ standard
• US0: conforming to USM™ standard
• AD99: standard single Eurocard, 100mm x 160mmm
• SA1: 32mm x 42mm

Weight:
• P599: 65g
• US0: 20g
• AD99: 90g
• SA1: 16g

Environmental Specifications

Temperature range (operation):
• 0..+60°C
• Airflow: min. 10m³/h

Temperature range (storage): -40..+85°C

Relative humidity (operation): max. 95% non-condensing

Relative humidity (storage): max. 95% non-condensing

Altitude: -300m to + 3,000m

Shock: 15g/11ms

Bump: 10g/16ms

Vibration (sinusoidal): 2g/10..150Hz

Conformal coating on request

Safety

PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers

EMC

Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst)

Software Support

Nios® sample design for Quartus® II development tools

Flash update tools for Windows®, Linux, VxWorks®

Driver software depending on implemented FPGA functions

For more information on supported operating system versions and drivers see Software.