Log in News & Media | Downloads | Corporate | Careers | Legal Notes
(215) 542-9575
sales@menmicro.com

EK6N - ESM Starter Kit with EM1N / MPC5200B COM
 

Evaluation Set for Embedded System Modules

This product has been discontinued.

Embedded System Modules are complete computers on a module. A final application consists either of a stand-alone ESM, an ESM with an application-specific carrier card and/or an ESM with additionally plugged PCI-104 modules.

Download data sheet

  • EK6N Product ImageEK6N ESM Starter Kit with EM1N / MPC5200B COM
  • EK6N Product Image

Main Features

  • EM1N with MPC5200B / 384 MHz
  • 256 MB DDR SDRAM, 1 GB NAND Flash
  • 2 MB SRAM, 16 MB graphics memory
  • 2 Fast Ethernet, COM, USB, 2 CAN bus
  • FPGA with additional I/O:
  • Graphics, SPI, 4 UARTs, IDE
  • ATX-compatible carrier card:
  • 1 ESM slot, 3 PCI slots
  • Graphics, touch, 1 USB 2.0, IDE, 2 COMs
  • Accessories:
  • External PSU, PCI-104 adapter
  • VGA cable, RJ45 to D-Sub cable
EK6N Product Image

Technical Data

ESM Carrier Card
  • One ESM slot
  • J1 and J2 assembled
  • I/O connectors
    • USB 2.0
    • RS232/422/485 COM10 interface
    • Quad serial I/O interface (3 COM, GPIO)
    • IDE connector
    • TFT connector
    • Touch panel connector
    • VGA connector
  • PCI interface
    • Three PCI slots
    • 32-bit/32-MHz, 5V V(I/O)
    • Compliant with PCI Specification 2.2
  • Reset button and power LED
ESM Module EM1N
  • CPU
    • PowerPC MPC5200B
    • 384MHz
  • Memory
    • 256MB DDR SDRAM, soldered
    • 1GB soldered NAND Flash, FPGA-controlled
    • 2MB boot Flash
    • 2MB battery-backed SRAM
    • 16MB SDRAM (graphics/NAND firmware)
  • Mass storage
    • Fast IDE port for IDE devices (40-pin, via ESM carrier)
    • PIO mode 0 support
    • 1GB soldered ATA NAND Flash, FPGA-controlled
  • Graphics: TFT/VGA and touch panel, connectors on carrier card
  • I/O at front panel
    • One USB 1.1, on Series A connector
    • Two 10/100Base-T Ethernet channels, on RJ45 connectors
    • One RS232 UART (COM1), on RJ45 connector
  • I/O via onboard connectors
    • Two CAN bus interfaces, via SA-Adapters
  • I/O via carrier card
    • Accessible on ESM carrier
    • One UART interface (COM10), on D-Sub connector
    • Three UART interfaces (COM11..COM13), via SA-Adapters
    • 5 GPIO lines, on 40-pin serial I/O connector
  • Functions in FPGA
    • Main bus interface
    • 16Z070_IDEDISK - IDE controller for NAND Flash
    • 16Z043_SDRAM - Additional SDRAM controller (16MB)
    • 16Z023_IDENHS - IDE controller (PIO mode 0; non-hot-swap)
    • 16Z044_DISP - Display controller (800 x 600, 60Hz/70Hz, 6-bit RGB)
    • 16Z031_SPI - SPI touch panel controller
    • 16Z087_ETH - Ethernet controller (10/100Base-T)
    • 16Z025_UART - UART controller (controls COM10..COM13)
    • 16Z034_GPIO - GPIO controller (5 lines)
    • The FPGA offers the possibility to add customized I/O functionality. See FPGA.
  • PCI interface
    • 32-bit/32-MHz PCI interface at PCI-104 connector J1
    • Compliant with PCI Specification 2.2
    • Supports four external masters
Accessories
  • External PSU
  • VGA cable
  • RJ45 to D-Sub cable
  • Adapter for mounting of one PCI-104 module
  • SA-Adapter ribbon cable for 40-pin connector with four 10-pin connectors (not included in standard delivery)
Electrical Specifications
  • Supply voltage/power consumption:
    • +24V (-35%/+50%), 0.3A
  • MTBF: 179,474h @ 40°C according to IEC/TR 62380 (RDF 2000)
Mechanical Specifications
  • Dimensions:
    • Carrier: conforming to Mini-ATX standard (PCB: 170mm x 150mm)
    • ESM: conforming to ESM specification (PCB: 149mm x 71mm), Type I-S
  • Weight:
    • Carrier: 200g
    • ESM: 90g (w/o heat sink)
Environmental Specifications
  • Temperature range (operation):
    • 0..+60°C
    • Airflow: natural convection
  • Temperature range (storage): -40..+85°C
  • Relative humidity (operation): max. 95% non-condensing
  • Relative humidity (storage): max. 95% non-condensing
  • Altitude: -300m to + 3,000m
  • Shock: 15g/11ms
  • Bump: 10g/16ms
  • Vibration (sinusoidal): 2g/10..150Hz
Safety
PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
BIOS
MENMON
Software Support
  • VxWorks
  • Linux (ELinOS)
  • QNX
  • PikeOS (partitionable RTOS) certified platform
  • MSCAN/Layer2 support: MEN Driver Interface System (MDIS for all supported operating systems)
  • For more information on supported operating system versions and drivers see Software.

FPGA

Ordering Information

SA-Adapters
08SA01-00
SA1 - RS232 Interface Adapter

RS232, not optically isolated, 0..+60°C

Details
08SA02-00
SA2 - RS422/RS485 Interface Adapter

RS422/485, half duplex, optically isolated, 0..+60°C

Details
08SA02-01
SA2 - RS422/RS485 Interface Adapter

RS422/485, full duplex, optically isolated, 0..+60°C

Details
08SA03-00
SA3 - RS232 Interface Adapter

1 RS232, optically isolated, 0..+60°C

Details
08SA08-00
SA8 - CAN Bus ISO High-Speed Interface Adapter

CAN bus ISO high-speed, optically isolated, 0..+60°C

Details
08SA22-00
SA22 - IBIS Slave/Master Interface Adapter

IBIS master, -40..+85°C screened

Details
08SA22-01
SA22 - IBIS Slave/Master Interface Adapter

IBIS slave, -40..+85°C screened

Details
08SA25-00
SA25 - GPS Receiver Interface Adapter

GPS receiver, isolated, -40..+85°C screened

Details

Software

Linux
13Z077-90

Linux native driver (MEN) for 16Z077_ETH and 16Z087_ETH

This product is designed to work under ELinOS Embedded Linux by SYSGO. For more information and product support please contact www.sysgo.com.

13MD05-90

MDIS5 System (and Device Driver) Package (MEN) for Linux. This software package includes most standard device drivers available from MEN.

10EM01-90

Linux BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12, F12N and PP1 under ELinOS 5.0 (rpm for direct installation in ELinOS)

VxWorks
13Z015-06

MDIS5 low-level driver sources (MEN) for 16Z029_CAN (MSCAN/Layer2)

10EM01-60

VxWorks BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12N and F12

QNX
10EM01-40

QNX 6.3 SP3 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

13Z087-40

QNX native driver (MEN) for 16Z087_ETH

13Z025-42

QNX 6.5 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z025-41

QNX 6.4 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z025-40

QNX 6.3 native driver (MEN) for 16Z025_UART and 16Z125_UART

13Z015-06

MDIS5 low-level driver sources (MEN) for 16Z029_CAN (MSCAN/Layer2)

10EM01-42

QNX 6.5.0 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

10EM01-41

QNX 6.4.1 BSP (MEN) for EM1, EM1A, EM1N, EK6, EK6N, F12 and F12N

PikeOS

This product is designed to work under PikeOS by SYSGO. PikeOS is a real-time operating system for use in safety and mission-critical systems which can be certified according to DO-178B DAL-B and EN 50128 SIL 4. For more information and product support please contact www.sysgo.com.

Firmware/BIOS
MENMON is an MEN firmware/BIOS for PowerPC platforms.
14EM01-00

MENMON (Firmware) for EM1, EM1A, EM1N, F12 and F12N (object code)

FPGA
16EK06N00

EK6N FPGA development package (MEN), including net lists of all IP cores being part of the EK6N standard factory configuration, top file, and Altera Quartus project (license not included in EK6N starter kit)