Follow Us
F14 - Intel Pentium M CPU Board
3U CompactPCI
This product has been discontinued.Equipped with the high-performance Intel 2-GHz Pentium M down to the 1-GHz ultra low voltage Celeron M processor, the F14 is a 4 HP/3U CompactPCI board, designed for embedded systems with high computing/graphics performance and low power consumption.
F14 configuration example (shown without heat sink)
F14 Configuration example equipped with a heat sink
F14 configuration example with a F603 side card (USB/COM) and a hard disk
F14 configuration example with a F603 side card (USB/COM) with a CompactFlash and an adapter with second CompactFlash
F14 configuration example with a F603 (USB/COM) side card and a CompactFlash
F14 configuration example with a F603 side card (USB/COM)
F14 configuration example with a F600 side card (2 COM extensions, 1 SATA hard disk)
F14 configuration example with a F603 side card (USB/COM) with a hard disk and a CompactFlash
F14 configuration example with a heat sink and a CompactFlash
F14 configuration example equipped with a heat sink and an adapter for a CompactFlash
F14 configuration example with a heat sink and an adapter for a CompactFlash and a battery
Main Features
- ULV Celeron M 373, 1 GHz
- Up to Pentium M 760, 2 GHz
- PCI Express four x1 links
- 4 HP system master or stand-alone
- 32-bit CompactPCI or cPCIe
- Up to 2 GB DDR2 DRAM soldered
- CompactFlash slot
- 2 SATA interfaces
- Video via VGA and 2 SDVO
- 2 Gigabit Ethernet (PCIe)
- Up to 8 USB 2.0
- High Definition audio
- Board controller
- -40 to +85C screened versions
Technical Data
- ULV Celeron M 373 up to Pentium M 760
- 1.0 to 2.0GHz processor core frequency
- 400MHz or 533MHz front-side bus frequency
- Chipset
- Northbridge: Intel 915GM
- Southbridge: Intel ICH6M
- Up to 1MB L2 cache integrated in Celeron M or 2MB L2 cache integrated in Pentium M
- Up to 2GB SDRAM system memory
- Soldered
- DDR2
- 400MHz or 533MHz memory bus frequency
- Dual-channel, 2x64 bits
- 4Mbits boot Flash
- Serial EEPROM 2kbits for factory settings
- CompactFlash card interface
- Via onboard IDE
- Type I
- True IDE
- DMA support
- Parallel IDE (PATA)
- One IDE port for local CompactFlash
- Serial ATA (SATA)
- Two channels via side-card connector, or: one channel via side card and one channel via rear I/O
- Transfer rates up to 150MB/s
- Integrated in 915GM chipset
- Analog CRT DAC interface support
- Supports max. DAC frequency up to 400 MHz
- 24-bit RAMDAC support
- Maximum resolutions: 2048 x 1536 pixels 16M colors @ 75Hz refresh rate (analog); 1600 x 1200 pixels 16M colors @ 60Hz (digital)
- Incorporates PanelLink Digital technology (Silicon Image)
- VGA connector at front panel
- Two SDVO ports available via side-card connector
- Two additional DVI connectors at front panel optional via side card
- Simultaneous connection of two monitors
- USB
- Two USB 2.0 ports via Series A connectors at front panel
- Four USB 2.0 ports via side-card connector
- Two USB 2.0 ports via rear I/O on request
- UHCI and EHCI implementation
- Data rates up to 480Mbit/s
- Ethernet
- Two 10/100/1000Base-T Ethernet channels, or: one 10/100/1000Base-T and one 10/100Base-T channel
- RJ45 connectors at front panel
- Gigabit Ethernet connected by two x1 PCIe links
- Onboard LEDs to signal activity status and connection speed
- High Definition (HD) audio
- Accessible via side-card connector
- VGA
- Two USB 2.0 (Series A)
- Two Ethernet (RJ45)
- Board controller
- Real-time clock, buffered by a GoldCap or alternatively a battery
- Watchdog timer
- Temperature measurement
- One user LED
- Reset button
- Two x1 links to connect local 1000Base-T Ethernet controllers
- Two x1 links for extension through side-card connector, or:
- Three x1 links if one Gigabit Ethernet channel is replaced by Fast Ethernet
- Data rate 250MB/s in each direction (2.5 Gbit/s per lane)
- Compliance with CompactPCI Core Specification PICMG 2.0 R3.0
- CompactPCI Express support (EXP.0 R1.0)
- System slot
- 32-bit/33-MHz CompactPCI bus
- V(I/O): +3.3V (+5V tolerant)
- Board can be supplied with +5V only, all other voltages are generated on the board
- Backplane connectors used only for power supply
- Supply voltage/power consumption:
- +5V (-3%/+5%), approx. 2.5A (ULV Celeron M 373), approx. 7.5A (Pentium M 760)
- +3.3V (-3%/+5%), approx. 1A
- +12V (-10%/+10%), approx. 10mA
- If the board is supplied with 5V only (typically without a bus connection), the 3.3V are generated on the board and fed to the backplane (3A max.) No external 3.3 V voltage may be applied in that case!
- MTBF: 86,600h @ 40°C (derived from MIL-HDBK-217F)
- Dimensions: conforming to CompactPCI specification for 3U boards
- Weight: 370g
- Temperature range (operation):
- 2GHz Pentium M760: 0..+60°C
- Conditions: airflow 1.5m/s, typical power dissipation 32W, with Windows XP operating system, 1 Gb Ethernet and hard disk, without CPU clock reduction
- 1GHz Celeron M373: -40..+85°C
- Conditions: airflow 1.5m/s, typical power dissipation 16W, with Windows XP operating system, 1 Gb Ethernet and hard disk, without CPU clock reduction
- Temperature range (storage): -40..+85°C
- Relative humidity (operation): max. 95% non-condensing
- Relative humidity (storage): max. 95% non-condensing
- Altitude: -300m to + 3,000m
- Shock: 15g/11ms
- Bump: 10g/16ms
- Vibration (sinusoidal): 2g/10..150Hz
- Conformal coating on request
- Windows
- Linux
- VxWorks
- QNX
- For more information on supported operating system versions and drivers see Software.
Options
- Celeron M 373 ULV, 1.0GHz
- Celeron M 370, 1.5GHz
- Pentium M 738 LV, 1.4GHz
- Pentium M 745 LV, 1.8GHz
- Pentium M 760, 2.0GHz
- System RAM
- 256 MB, 512 MB, 1 GB or 2 GB
- CompactFlash
- 0 MB up to maximum available
- Simultaneous connection of two monitors
- 9-pin D-Sub connector with one or two 10/100Base-T ports instead of two RJ45 connectors
- Two M12 connectors with two 10/100/1000Base-T ports instead of two RJ45 connectors on 8HP
- One SATA channel (instead of one side-card channel)
- Two USB 2.0 ports
- For retention of time/date data after a power off of more than 8-10 hours. When a 1.8" PATA hard disk is used, no battery can be used on the CPU board
- Depends on system configuration (CPU, hard disk, heat sink...)
- Minimum: -40°C (all processors)
- Maximum:
- +60°C (Pentium M 760)
- +85°C (Celeron M 373)
Ordering Information
2 Gigabit Ethernet on Lemo railway compliant connectors, 1 COM extension (SA-Adapter not included), SATA hard disk slot, for F14 and compatible SBCs, conformally coated, -40...+85°C screened
DetailsCompactFlash card, 16 GB, -40 to +85°C
CompactFlash card, 2 GB, Type I, fixed bit set, -40 to +85°C
CompactPCI 19" 4U/24HP desktop system for 3U cards, 3-slot 3U CompactPCI backplane, system slot right, 1U fan tray with 1 fan, 8 HP space for 1 pluggable PSU
Details
CompactPCI 19" 4U/84HP rack-mount enclosure for 3U cards (vertical), 4+4-slot 3U CompactPCI / CompactPCI Serial hybrid backplane, prepared for rear I/O, 250W power supply wide range 90..264VAC on rear, 1U fan tray with 2 fans included, 0..+60°C
DetailsMEN delivers turn-key systems completely installed (hardware, operating system, accessories), wired and tested. Different rack sizes, power supplies and backplanes on request.
For details please contact your local sales representative.
CompactFlash card, 8 GB, Type I, fixed bit set, -40 to +85°C
CompactFlash card, 4 GB, Type I, fixed bit set, -40 to +85°C
CompactPCI 3U 1-slot backplane for stand-alone operation of F14, F15, F17, F18, F19P, F21P, F22P, F23P: 32-bit/33-MHz with rear I/O, 3.3V supply, ATX-power, power, JTAG, IPMB and utility connection, 6x screw connection M3
3U CompactPCI to CompactPCI Express side card with 1 USB, 1 COM, 1 DVI, SATA hard disk slot, for F14 and compatible SBCs, 0..+60°C
Details
3U CompactPCI side card with 2 USB and 1 COM extension, SATA hard disk and CompactFlash slot, for F14 and compatible SBCs, mounted to the right of the SBC, 0..+60°C
Details
1 DVI-D and 1 audio at front, SATA hard disk slot, for F14 and compatible SBCs, 4HP, 0..+60°C
Details 2 DVI-D, 1 audio, 1 COM (via SA-Adapter) at front, SATA hard disk slot, for F14 and compatible SBCs, 8HP, 0..+60°C
DetailsSoftware
Linux MDIS5 low-level driver sources (MEN) for generic SMBus driver for F14, F15, F17, F18, F19P, F21P, F22P, F75P, G20, G22, D9, D601, F600 and F601, A19, A20, F217, CB70C, SC24, AF2, BC50M, BC50I, BL50W and MH50C
This product is designed to work under ELinOS Embedded Linux by SYSGO. For more information and product support please contact www.sysgo.com.
MDIS5 System (and Device Driver) Package (MEN) for Linux. This software package includes most standard device drivers available from MEN.
Windows Windows HD Audio driver (Realtek) for F14, F15, F17, F18, F19P, F21P, F22P, F23P, D9 and A19
Windows USB2UART driver (FTDI) for F14, F15, F17, F18, F19P, F21P, F22P, F23P, D9, A19, A20, XM2 and XM50 / XM51 / F50P / F50C hosts
Windows chipset driver (Intel) for F14, F15, F17, F18, F18E, F19P, F21P, F22P, G20, G22, XM2, CB70C, D9, D6, D7, D601, A19 and A20
Windows chipset graphics driver (Intel) for F14 and D601
Windows network driver (Intel) for F14, F15, F17, F18, D9, D6, D7, D601, A19, A20 and P601, P602
Windows Installset (MEN) for F14, F15, F17, F18, D9, D601, A19 and A20
Windows XP Embedded BSP (MEN) for F11S, F14, F15, F17, F18, F19P, F21P, G20, XM1, XM1L, XM2, MM1, MM2, DC1, DC2, DC13, RC1, BC50I, BC50M, BL50W and BL50S
MDIS4/2004 / MDIS5 Windows driver (MEN) for LM63 on SMBus for F14, F15, F17, F18, D9 and D601
VxWorks MDIS5 low-level driver sources (MEN) for F14, F15, F17, F18, D9, D601, A19 and A20 board controller
MDIS5 low-level driver sources (MEN) for generic SMBus driver for F14, F15, F17, F18, F19P, F21P, F22P, F75P, G20, G22, D9, D601, F600 and F601, A19, A20, F217, CB70C, SC24, AF2, BC50M, BC50I, BL50W and MH50C
VxWorks driver (MEN) for USB-to-UART bridges on F600, F601, F602, F603, F604 and F606
MDIS5 low-level driver sources (MEN) for F14, F15, F17, F18, D9, D601, A19 and A20 board monitoring
MDIS5 low-level driver sources (MEN) for LM63 on SMBus for F14, F15, F17, F18, F19P, D9, D601, A19 and A20
VxWorks BSP (MEN) for F14 and D601
QNX QNX 6.3.0 installation support files (QNX and MEN) for F14, F15, F17, F18, F19P, XM1, XM2 and MM1
MDIS5 low-level driver sources (MEN) for F14, F15, F17, F18, D9, D601, A19 and A20 board controller
MDIS5 low-level driver sources (MEN) for generic SMBus driver for F14, F15, F17, F18, F19P, F21P, F22P, F75P, G20, G22, D9, D601, F600 and F601, A19, A20, F217, CB70C, SC24, AF2, BC50M, BC50I, BL50W and MH50C
MDIS5 low-level driver sources (MEN) for F14, F15, F17, F18, D9, D601, A19 and A20 board monitoring
MDIS5 low-level driver sources (MEN) for LM63 on SMBus for F14, F15, F17, F18, F19P, D9, D601, A19 and A20
System BIOS for F14 and D601
Intel software development products such as analyzers, compilers, threading tools etc. can be downloaded under www.intel.com/cd/software/products/asmo-na/eng/index.htm.
IA-32 Intel Architecture Software Developer's Manuals are available under www.intel.com/products/processor/manuals/index.htm.
Documentation
F14 User Manual
F14 Errata (on request)
F14 Data Sheet
Product Compatibility Matrix: CompactPCI/PlusIO CPU Boards and Side Cards
Product Compare Chart: 3U CompactPCI/PlusIO CPU Cards
Product Compare Chart: 3U CompactPCI/PlusIO Extension Cards
Product Compare Chart: 3U CompactPCI/PlusIO Peripheral Cards
Application Examples
A 3U CompactPCI SBC with an Intel Core 2 Duo processor is used to control a medical robot that performs knee surgery.
Modular 19-inch systems like 3U CompactPCI or CompactPCI Serial are ideal for internet applications in trains like infotainment, exchange of train diagnosis data or transfer of surveillance data.
Modular 19-inch systems like 3U CompactPCI or CompactPCI Serial are ideal for passenger information solutions in transportation applications.
This control platform for intelligent well systems is realized as a pre-validated 3-slot 3U 24HP CompactPCI system with its own rugged power supply unit.
This application is a combination of a digital video recorder and a video display server and is part of a larger communication and surveillance system based on CompactPCI.