RS1 - Managed 8-Port Rugged Ethernet Switch with PoE
IP67 Industrial Stand-Alone Device
This product has been discontinued.The RS1 is a managed industrial, IP67 stand-alone Fast Ethernet switch that provides eight Ethernet channels and a Gigabit uplink port on M12 connectors
Main Features
- Managed 8-port rugged Ethernet switch
- Rugged aluminum enclosure (220 x 130 x 70 mm)
- Fanless and maintenance-free
- 8 Fast Ethernet ports via M12 connectors
- 1 Gigabit uplink port via M12 connector
- Power over Ethernet (PoE) PSE (ports 1 and 2)
- Configuration via CLI (RS232, Telnet or SSH), SNMP ver. 3 or ext. dongle
- 2x 24 VDC or 110 VDC nom. redundant power supply, service interface via M12 connectors
- Status LEDs for ports, power and more
- -40 to +70(+85)°C operating temperature
- EN 50155 class Tx (railways) and IP67 compliant
- ISO 7637-2 compliant (E-mark for automotive)
Technical Data
Key Features
- Simple Switch replacement: configuration can be done via external dongle without any tools
- High-speed non-blocking, store-and-forward switching
- Eight 10/100-T ports at front panel (Electrical isolation: 1500 Vrms)
- One Gigabit uplink port at front panel
- Port configuration: copper, 10/100 Mbit/s
- Auto-negotiation / Auto MDI/MDIX crossover on all ports / manual configuration possible
- Layer2-based Policy Control List
- 8K MAC address lookup table with automatic learning and aging
- Up to 4096 VLANs
- Rapid Spanning Tree Protocol and Multiple Spanning Tree Protocol to ensure loop free topology formation
- Reducing multicast traffic in the network through multicast snooping - IGS (IPv4) and MLDS (IPv6)
Management Firmware System Features
- Saving and restoring user configurations
- Software upgrades through TFTP
- System logs (syslog) and e-mail alerts for critical events
- Remote monitoring (RMON) and alarm generation
- Displaying the running configuration in the form of CLI commands
- Management interfaces through
- CLI (RS232 console, Telnet, SSH)
- SNMP v3
- Switch configuration can be loaded from external dongle
Management Firmware Security Features
- User authentication using 802.1x
- Controlling management access through SNMP and CLI only from authorized managers
- MAC based access list (ACL) for traffic filtering
- Rate-limiting and storm control to prevent packet flooding from malicious peers
Supported Protocols and Standards
- DHCP client / server / relay (IEEE 1394)
- Ethernet flow control (IEEE 802.3x)
- GARP (VLAN-aware bridging)
- GVRP/GMRP support (IEEE 802.1D, 2004)
- Hypertext Transport Protocol (HTTP) Server for Remote Management and Monitoring (RFC2626)
- HTTP Secure (HTTPS) - HTTP-based Remote Management over encrypted data channel (RFC2818)
- IGMP snooping / IGMP proxy / IGMP Querier / MLD Discovery (RFC 4541)
- Link aggregation LACP / EtherChannel (IEEE 802.3ad, 2005)
- Link Layer Discovery Protocol LLDP (IEEE 802.1ab, 2005)
- Multiple Spanning Tree (MSTP) (IEEE 802.1s)
- Path MTU Discovery Protocol (PMTUD) (RFC 1984)
- Priority-based switching, Quality of Service/DiffServ, tagged frames, Layer2-based 801.1Q VLAN-ID packet routing (IEEE 802.1p)
- Port-based authentication with EAP (IEEE 802.1x - REV2004/RFC3748)
- Power over Ethernet support (IEEE 802.3af / IEEE 802.3at, Type 1)
- Rapid Spanning Tree Protocol (RSTP IEEE 802.1w)
- Remote Network Monitoring Information Base v1 (RFC2819)
- Secure Shell (SSH) for Remote Configuration (CLI) over secure channel
- Secure Sockets Layer - Encrypted Data Exchange (RFC5246)
- SNMP v1, v2c, v3 management
- Syslog (RFC 5424)
- TCP/IP v4 and v6
- TFTP (RFC 1350)
- VLAN/port-based VLANs GVRP/MVRP (IEEE 802.1Q Rev D5.0, 2005)
Power Over Ethernet Features
Power over Ethernet functions on ports 1 and 2
- PSE (Power Sourcing Equipment) function
- Supplies one PD class 0 device or two PD class 2 devices (up to 15 W total)
Service Interface
- M12 connector at front
- RS 232 / V24
- I²C interface for external dongle
Front I/O
- Eight Ethernet ports via M12 connectors
- Gigabit uplink port
- 8-pin M12 connector, A-coded
- One service interface via M12 connector
- Two redundant power inputs via M12 connectors
- Link and activity Ethernet status LEDs (2 per channel)
- Power over Ethernet status LEDs
- Status LEDs for power, reset and error codes
Electrical Specifications
- Power input
- Nominal input voltage 24 VDC (9 to 36 V) or 110 VDC (77 to 150 V) according to EN 50155
- Two redundant inputs
- Power-on threshold: 0.7xUn = 16.8 V (for 24 VDC PSU) or 77 V (for 110 VDC PSU)
- Power change-over threshold (when a secondary power source is connected): 12 V (for 24 VDC PSU) or 66 V (for 110 VDC PSU) (lower input voltage results in automatic switch to secondary power source)
- Minimum input voltage when no secondary power source is connected: 9 V (for 24 VDC PSU) or 66 V (for 110 VDC PSU)
- EN 50155 power interruption class S2
- Isolation (according to EN 50155)
- 1500 Vrms
- Power consumption at Unom (24 V): 24 W (incl. 15 W PoE)
Mechanical Specifications
- Dimensions: 220 mm x 130 mm x 70 mm (without connectors)
- Prepared for wall or DIN-rail mounting with special mounting plates (available separately)
- Weight: 1.9 kg
Environmental Specifications
- Temperature range (operation):
- -40..+70°C (+85°C) with up to 85°C for 10 minutes according to class TX (EN 50155)
- Airflow: natural convection
- Temperature range (storage): -40..+85°C
- Relative humidity (operation): max. 95% non-condensing
- Relative humidity (storage): max. 95% non-condensing
- Altitude: -300 m to + 3000 m
- Shock: 50 m/s², 30 ms (EN 61373)
- Vibration (function): 1 m/s², 5 Hz - 150 Hz (EN 61373)
- Vibration (lifetime): 7.9 m/s², 5 Hz - 150 Hz (EN 61373)
- Climatic tests according to EN68068
- IP67 compliant
- Fully EN 50155-compliant (Power Interruption Class 2, Temperature Class TX)
MTBF
250 185 h @ 40°C according to IEC/TR 62380 (RDF 2000)
Safety
Flammability (PCBs)
- PCBs manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
EMC
- Tested according to the following railway standards:
- EN50121 (radio disturbance)
- EN61000-4-2 (ESD)
- EN61000-4-4 (burst)
- EN61000-4-5 (surge)
- Conforming to E1 requirements of the German Federal Motor Transport Authority
- Tested according to the following automotive standards:
- CISPR25/CISPR16 (radiated emission)
- ISO7637-2 (conducted emission - power line)
- ISO7637-2 (conductive immunity - power line)
- ISO7637-3 (capacitive immunity - signal line)
- ISO11452-2, ISO11452-5 (radiation immunity)
- EN50121 (radio disturbance)
Software Support
Firmware for configuration and management included
Options
Ethernet Switch Functions / Mechanical Specifications
No Gigabit Uplink port
Electrical Specifications
Other nominal input voltages: 36, 48, 72 or 96 VDC
- Wide input range (according to EN 50155): 0.7 x nominal voltage < nominal voltage < 1.25 x nominal voltage
Ordering Information
Software
Firmware/BIOS
14ETSW-00
Ethernet Switch Firmware for managed RSx, SFx, F302 and G302 models
Documentation
Data Sheets
User Manuals
Errata & Technical Information